What does a switch do when it doesnt have an entry for the destination MAC address in its MAC table?
|
A switch has some intelligence and operates on layer 2 of the OSI model. In this lesson, I’ll demonstrate how a switch learns MAC addresses. Let me show you an example of three computers connected to a switch: Show
 There’s a switch in the middle and we have 3 computers. All computers have a MAC address but I’ve simplified them. Our switch has a MAC address table and it will learn where all the MAC addresses are in the network. Let’s send something from H1 to H2:
H1 is going to send some data meant for H2, thus it will create an Ethernet frame which has a source MAC address (AAA) and a destination MAC address (BBB). Our switch has a MAC address table and here’s what will happen: Nội dung chính
The Ethernet switch has become an integral part of the world’s LAN infrastructure. At its core, the Ethernet is a shared network, each node contending for access to precious bandwidth and dealing with the repercussions of collisions. Before switches, hubs received Ethernet frames and forwarded them to every connected device. There was no privacy or security and performance was poor. What the network needed was a more logical device that could make decisions for where to send data and block the traffic flow to irrelevant devices. The switch accomplishes these requirements by executing four basic functions: Learning, Forwarding, Filtering and Flooding. These functions are present in a switch by default, right out of the box. No configuration is necessary. Now, imagine that we have a switch with four ports and four user workstations. We’ll call these workstations A, B, C and D and we’ll number the ports 1, 2, 3 and 4. The chart below provides a list of the four workstations and their respective MAC addresses.
It’s important to remember that every Ethernet frame contains two MAC addresses. The source address is always a unicast MAC address. The destination address will be either a unicast addresses, a multicast address or a broadcast address. The switch has the ability to read and process both the destination address and the source address. LearningLet’s start with learning. Switches need to keep track of the MAC addresses of all connected devices. Without the learning function, the switch would not know to which port the destination device is connected. At the center of the learning function is a part of the switch’s memory. We refer to this memory location as the MAC Address Table. As the switch receives a data packet, it reads the source address and maps the port number to the MAC address in that source field. The following diagram shows what a MAC Address Table entry looks like if Workstation A is plugged into Port 1 of our switch and sends a frame.
Because the MAC address table is in memory, not persistent storage, the table is also temporary. In fact, MAC address tables have a timer that, once expired, results in the deletion of the entry. There is an important reason for this. Let’s say Workstation A is plugged into Port 1 then quickly switches to Port 2. The same MAC address will appear on both Port 1 and Port 2. The switch will use the port that has the longest timer, indicating that it is the most recent entry and therefore the most accurate. Most switches have a default timer of 300 seconds (5 minutes). But this is only half of the process. As you can see in the above MAC Address Table, no other device has been identified on our switch. Let’s continue with our scenario. Workstation A was trying to send a frame to Workstation D. But where is Workstation D? From the switch’s perspective, this is unknown. The switch must rely on another function to find the destination. This second function is called Flooding. FloodingFlooding means that the switch sends the incoming frame to all occupied and active ports (except for the one from which it was received). In essence, flooding is when a switch pretends to be a hub. There are two basic reasons why a switch will flood a frame. 1. When the switch receives a broadcast, it has no choice but to continue the broadcast. Protocols like ARP and DHCP (among others) rely on these broadcasts for their basic function. The following diagram is an example of what an Ethernet frame header might look like as a broadcast.
2. When the switch receives a frame dedicated for a particular destination but that destination does not have an entry in the MAC Address Table, the switch has no choice but to flood the frame. The goal of this flood is that the device using the MAC address in the destination of the frame will receive the flood and respond to the message. If that device responds, then the switch can learn their MAC address and map it to the port into which the message arrives. The following diagram is an example of what an Ethernet frame header might look like. Notice that the destination MAC address does not match the MAC Address Table above.
The following diagram shows the new MAC Address Table now that the response to the flood has been received.
ForwardingNow that Workstation A and Workstation D are both identified by their port numbers, the switch can do what switches do. Workstation A can now continue its conversation with Workstation D. But this time, when the switch receives the frame (see the diagram below), it first looks up the destination address in the MAC Address Table. It then forwards the frame to that specific port. In our scenario, Workstation A is connected to Port 1 and Workstation D is connected to Port 4. When the switch receives the frame, it immediately forwards that frame to Port 4.
FilteringSo what about Workstations B and C? Well, due to filtering, Workstations B and C are none the wiser. Let’s fill in the rest of our MAC table.
The switch intentionally filters out ports 2 and 3, only forwarding the data to the destination MAC address identified in the frame header. These four default functions are just the beginning. Managed switches can include performance optimization, security, monitoring, diagnostics and more. But that’s for another discussion. Recommend courses to become a switch expert
SubscribeNever miss another article. Sign up for our newsletter. What does a switch do if it can't find the destination MAC address?When a switch doesn't have the destination mac address in its mac address table, it floods the frame to all other port except the receiving port. How is the MAC address related to a switch?A MAC Address is given by the manufacturer and it is embedded in the chip that allows your device to connect to a network. For a network switch, it is likely to have many MAC addresses, since one MAC address is assigned to every interface on the switch. What will switch do if the MAC address is not found in its MAC address table?When the destination MAC address is not found in the MAC address table, the switch forwards the frame out of all ports (flooding) except for the ingress port of the frame.
What does a switch do if it receives a packet with unknown destination MAC address?Explanation. When a switch receives a frame from a destination it does not know, it inserts the source mac address into its CAM table (a table which maps mac addresses to ports) and forwards the frame to all ports.
What a switch does when a switch doesn't find the matched destination MAC address in its switch table?When a switch receives a frame, it updates its MAC address table with the source MAC address and the port on which it received the frame. If the destination MAC address isn't in its MAC address table (unknown unicast), it floods the frame to all ports, except the port on which the frame was received.
What is the purpose of the MAC address table in a switch?The MAC address table is where the switch stores information about the other Ethernet interfaces to which it is connected on a network. The table enables the switch to send outgoing data (Ethernet frames) on the specific port required to reach its destination, instead of broadcasting the data on all ports (flooding).
|
